Nikon LS-10 Installation Guide for Windows Uživatelský manuál

<<CDNikon®Coolscan^InstallationGuideforWindows™Nikon,ELECTRONIC IMAGING

Chapter 1 IntroductionRegistrationCompleting and returning the enclosed Product Warranty Registration Card is very important to you. It is the only wa

lntrodu<tionChapter 1of colors available. Thousands or millions of colors will provide an excellent display of your image. If your system only supp

Chapter 2Setting Up CoolscanSetting Up CoolscanThis chapter will introduce you to the main components of the LS-10 and LS- lOE models, proper placemen

Setting Up Cools<anChapter 2Focus WheelThe focus wheel is used to fine-focus during scanning operation. This control is provided because of the wid

Chapter 2Setting Up CoolscanSCSI TerminationFigure 2.2 Coolscan’s rear panel - LS-IOE.The AC power switch and AC power connector should be familiar to

Setting Up CoolsconChapter 2The significance of the SCSI connector, DC power connector, and the configuration DIP switch is discussed in greater deta

Chapter 2 Setting Up Coolsranits base, or feet, to ensure that it won’t fall down. In this orientation, the “Nikon Coolscan” label on the front panel

Setting Up Cools<anChapter 28. Avoid places with extremely hot or cold temperatures (below 10 degrees Celsius or above 35 degrees Celsius).9. Avoid

Chapter 2Setting Up CoolstanSafety Precautions When Connecting AC Power to the LS-10EThe following precautions should be complied with when connecting

Setting Up CoolscanChapter 24. Never disassemble the scanner. It is very dangerous to touch the devices inside the unit due to high voltages, and the

NikonCoolscan™ Installation Guidefor the Windows Operating System

Chapter 2Setting Up CoolsranInstallation PrecautionsThe following guidelines should be observed when installing Coolscan:1. Make certain that power to

Setting Up CoolscanChapter 2Page 14Nikon Coolscan Installation Guide for Windows

Chapter 3The SCSI InterfaceThe SCSI InterfaceThe computer interface used exclusively with Coolscan is called a Small Computer System Interface (SCSI -

The SCSI InterfaceChapter 3The default SCSI ID number ofCoolscan, set at the factory, is ID #5.Determining Which SCSI ID Number to UseIf Coolscan is t

Chapter 3The SCSI InterfaceSetting the SCSI ID - IS-IDEIf necessary, the SCSI ID number of the LS-lOE can be set via a switch on the back of the scann

The SCSi interfaceChapter 3Default IDDIP Switch ConfigurationSCSI IDDIP#1 DIP #2 DIP #30 OffOffOff1 OnOff Off2Off OnOff3On OnOff4Off OffOn5On Off On6

Chapter 3The SCSI InterfaceTerminating the LS-10EThe LS-lOE is configured with two 50-pin SCSI connectors on the rear of the unit, as shown in Figure

The SCSI lnterfa<eChapter 3If switch #4 is in the ON position, Coolscan is internally terminated. If switch #4 is in the OFF position (the factory

Chapter 3The SCSI InterfarePlease proceed to the section The PC’s External SCSI Connector.SCSI Cables Used With the LS-10The SCSI flat cable provided

The SCSI InterfaceChapter 3(b) Non-chainable SCSI Flat Cable (not provided)SCSI 50-Pin ConnectorsConnector Protection Key-------------------Figure

FCC Radio Frequency Interference Statement for CoolscanThis equipment has been tested and found to comply with the limits for a class B digital devi

Chapter 3The SCSI InterfaceMake sure not to confuse the printer port connectors on the computer with the 25-pin DB25 SCSI connector, should this type

The SCSI InterfaceChapter 3Typical SCSI Connector on SCSI Controller CardCircuit Card SCSI ConnectorSCSI Flat Cable Pin 1 Indicator -Figure 3,8 The 50

Chapter 3The SCSI Interface(a) Closed SCSI ConnectorTo Remove Connector: Pry flat cable connector out gently with small flat screw driver Circuit Card

The SCSi Interface Chapter 3The SCSI ChainThe SCSI chain, as you learned earlier, is the electronic data and control bus that connects two or more SCS

Chapter 3The SCSI InterfaceExternal SCSI ConnectorInternalSCSI Connector,1^''ll .»Dtp Switches . » 'CaniMi.bai):::1 ^j-i- Icrmination

The SCSI InterfaceChapter 3Setting the SCSI Controller Card ConfigurationThe DIP switches, shown in Figure 3.11 are used to set the HO address for the

Chapter 3 The SCSI InterfaceInstalling the SCSI Controller Card Into the ComputerInstalling the SCSI controller card is not difficult, but requires so

The SCSI interfaceChapter 3Remove the lock down screw and slot cover plate at the back of the computer associated with the selected card. Save this sc

Chapter 3 The SCSI interfareSetting Up the SCSI Chain - LS-lOEThe LS-lOE can reside at any position in the SCSI chain. The two 50-pin connectors on t

The SCSI Interface Chapter 34. Connect a SCSI connector to the bottom SCSI connector on the back of Coolscan, since this is the end of the SCSI chain

TRANTOR-New Horizons in SCSI Design SOFTWARE LICENSE AGREEMENTIMPORTANT*YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE OPENING OR

Chapter 3The SCSI Interface3. Insert one end of the unused SCSI cable into the top SCSI connector on the back of Coolscan.4. Connect the other end of

The SCSI InterfaceChapter 3(a) Computer SCSI ControllerComputer Internal SCSI Termination Computer SCSI ConnectorUnused center SCSI Connector(b) SCSI

Chapter 3The SCSI InterfaceFigure 3.16 Multiple SCSI devices on the PC’s SCSI bus.Coolscan is at the end of the SCSI chain.Procedure (use the supplied

The SCSI InterfaceChapter 3chapter for the proper DIP switch setting. Because the PC is at the other end of the chain, it also must be terminated.It i

Chapter 3 The SCSI Interfacelength of all the SCSI cables used in the chain should not exceed 18 feet. A chain of more than 18 feet may result in lost

The SCSI lnterfa<eChapter 3Page 38Nikon Coolscan Installation Guide for Windows

Chapter 4Mounting the LS-10Mounting the IS* 10This chapter covers installation of the LS-10 model only. Proceed to Chapter Five if you are installing

Mounting the LS-10 Chapter 4Figure 4.1 K typical PC 5-1/4" half-height drive bay, as seen from the front of the computer.The Guide RailsBecause e

Chapter 4Mounting the LS-10Step 4. Remove the PC’s cover.Following the manufacturer’s instructions, remove the computer’s cover, providing access to

Mounting the LS-10Chapter 4holding the scanner and guide rails in front of the drive bay. Choose the holes and position of the guide rails (relative

AcknowledgmentsNikon acknowledges with gratitude the contributions of the Design, Planning and Production Sections of the Electronic Image Engineering

Chapter 4Mounting the LS-10Before Inserting Coolscnn into the Drive BayBefore inserting Coolscan into the chosen drive bay, make certain that the SCSI

Mounting the IS-10Chapter 4insertion). The cable’s connector should be oriented so that its key and ribbed side face upwards and is parallel with the

Chapter 4Mounting the LS-10Never attempt to connect power to the scanner while the computer’s power is on.Note that both ends of the power connector a

Mounting the LS-10Chapter 4Once the scanner is pushed into the computer, reposition or reinsert the lock tabs dealt with in Step 6, Procedure 4,1. The

Chapter 5Software InstallationSoftware InstallationNikon Scanner Plug-in SoftwareCoolscan is bundled with two scanning software programs and one utili

Software InstallationChapter 5Coolscan. This application has no menu. It will locate Coolscan, send the Eject Film command, then quit.Nikon Installer

Chapter 5 Software InstallationMain Menu Bar-Program ManagerFile Options Window HelpClick and drag down cFigure 5.2 The Windows Program Manager.The Fi

Software installationChapter 5ton. Similarly, you can exit the Nikon Installer at any time by clicking on the EXIT button.To complete the softwate in

Chapter 5Software InstallationNikon Scanner Sofhnrare installerWelcome to the Nikon Scanner Software Installer.This program will copy the scanner

Software InstallationChapter 5The Installation Options DialogThe next step entails selecting the application software which you want to ‘host,’ or con

Table of ContentsTable of Contents1- Introduction ...

Chapter 5 Software InstallationPath Selection tor Files The setup progiam will copy all files into the following directory.Path;CiSNIKONiIf you are i

Software InstallationChapter 5When using Coolscan with the included SCSI controller card, select the Copy FILE AND UPDATE CONFIG.SYS selection. Exper

Chapter 5Software InstallationNikon Scanner Software InstallSetup Succeeded!Be sure to fill out and send in the registration card to receive iuture up

Software InstallationChapter 5Path Selection for InstallerPlease enter the directory to install your application from.Path;A:\PSSETUP.EXEThis wi

Chapter 5Software InstallationInstallation MethodSelect an installation process.^viNew Installation!You will be installing new application software as

Software InstallationChapter 5Installing the SCSI Driver SoftwareCoolscan is interfaced to the computer through the SCSI bus. It is necessary to load

Chapter 5Software InstallationConclusionCongratulations! You have successfully completed installation of your Coolscan scanner and software. This conc

Software InstallationChapter 5Page 60Nikon Coolscan Installation Guide for Windows

TroubleshootingTroubleshootingFollowing are some common problems you may encounter in the installation of your scanner. Corrective action for each pro

TroubleshootingAction: PhotoStyler can only support one scanner driver at a time. If you have sufficient disk space, create a duplicate of the PhotoSt

Table of ContentsConnecting to the Internal SCSI Connector...23The SCSI Controller Card ..

TroubleshootingProblem; I get a system error when I'm scanning.Action: Make note of the exact error message that appears, then contact

Nikon Inc.Electronic Imaging Dept.1300 Walt Whitman Road Melville, NY I 1747- 3064 (516)547-4355© 1993 Nikon Inc. All brand names and p

Chapter 1 IntrodurtionIntroductionThank you for purchasing the Nikon Coolscan™ 35mm Film Scanner, and welcome to our family of electronic imaging pro

introductionChapter 1Chapter One - Introduction • (this chapter) Provides an overview of the Coolscan documentation package, product registration info